Why microfibre cloths need care
A microfibre cloth works with structure, not with chemicals. Fine fibres absorb water and dirt and hold both between the fibre ends. For this to work, the fibres must remain free: open, soft and uncoated. That is exactly what is lost during washing if temperature, detergent or drying are not right.
A cloth that has become hard barely absorbs water and glides differently over the surface. A clogged cloth leaves streaks. Both are avoidable without expensive special products – the most important rules are here.
Overview: Cleaning cloths and wash mitts for car care
Verified test results
- We currently have no verified test results from independent publishers on this topic. As soon as published tests exist, we will add them here with their source.
The most important points at a glance
- Separate cloths before washing by area of use: paint and glass, interior, wheels and heavily soiled areas.
- Wash microfibre cloths without fabric softener, without bleach and without added fragrances.
- Wash at moderate temperature and spin at low speed.
- Dry cloths in the air or at low temperature; high heat hardens the fibres.
Before washing: sort by area of use
Sorting is the most important step and takes only a few minutes. It prevents polish residues, waxes or wheel dirt from getting into the fibres of cloths that will later be used on paint.
Sort into at least three groups:
- Paint and glass: cloths that have only come into contact with clean paint, glass or drying work.
- Interior: cloths with dust, plastic care or textile abrasion.
- Wheels, sills, engine bay: cloths with brake dust, tar or heavily greasy dirt.
Colour system and labelling
A colour system makes sorting permanently easy: one colour per area of use. If you do not want to use different colours, you can mark the cloths with a permanent fabric pen on the edge or store them in labelled laundry bags. The only important thing is that the assignment remains after washing – otherwise a wheel cloth will sooner or later end up on the paint.
When a pre-wash makes sense
Cloths with dried polish or wax residues are best washed separately and pretreated. Heavily soiled cloths from the wheel area should never go in the same load as paint-related cloths.
The right washing temperature
Temperature is a compromise: warmth dissolves fats and care product residues, too much heat can permanently change the fine fibres. For regular washing, a moderate range in the lower to middle temperature window has proven effective.
| Type of wash | Temperature | Note |
|---|---|---|
| light soiling, interior cloths | cold to hand-warm | gentlest variant, sufficient for most loads |
| normal soiling, paint-related cloths | moderate warm range | reliably dissolves grease residues |
| heavily soiled cloths from the wheel area | higher warm range | wash separately from paint-related cloths |
Start with the lowest temperature that dissolves the dirt. If that is not enough, increase gradually. Do not boil microfibre cloths and do not wash them permanently at the upper end of the temperature range – the fibre thanks you with a longer service life.
Which detergent suits – and which does not
For microfibre: simple and liquid. Liquid detergents dissolve better than powder, whose grains can lodge in the fibres. Avoid additives that leave a film on the fibre.
| Detergent | Suitable | Reason |
|---|---|---|
| liquid detergent, neutral | yes | dissolves without residue |
| heavy-duty detergent with bleach | no | can attack fibres and colours |
| fabric softener | no | forms a film around the fibres and removes their absorbency |
| products with added fragrance or care film | no | residues remain in the fibre |
Dose sparingly. Less detergent is usually enough for microfibre because the fibres themselves absorb a lot of dirt. An extra rinse helps to rinse residues out completely.
Fabric softener, bleach and fragrances: better not
Fabric softener is the most common reason for hard, water-repellent cloths. It coats the fibres with a film that reduces absorbency. Bleach-containing products can attack the fine fibres and the dyes. Additives with fragrances also leave residues that can appear as streaking on glass and paint.
The wash cycle step by step
- Sort: put cloths into separate loads by area of use.
- Pretreat: rub heavily soiled areas with a little liquid detergent and leave briefly.
- Check the load: do not overload the drum; the cloths should be able to move.
- Dose detergent: add liquid detergent sparingly, do not use fabric softener.
- Select temperature: start with the low range and increase only if needed.
- Switch on an extra rinse if your machine offers it.
- Spin: at low speed so the fibres are not pressed.
After washing, remove the cloths from the drum promptly. If they are left damp in the machine, musty odours can develop that may remain after drying.
Spinning and drying
Spinning at high speed presses the fibres flat. A low setting is enough because microfibre releases water well. Then shake the cloths and dry them in the air – hung up or laid flat, with air circulation from both sides.
The tumble dryer is only suitable with caution. High temperatures can harden the fibres. If you dry anyway, choose the lowest setting and remove the cloths early. Drying on the radiator is not a good idea: direct heat can change the fibre.
Pretreat stubborn soiling
Polish residues and wax can be loosened by soaking the affected area before washing with a little warm water and a drop of liquid detergent. Loosen dried residues beforehand with a fingernail or a soft brush, do not scrape them out with a sharp object.
Resin, tar or insect residues do not belong in the normal wash while they are still sticky. Remove them roughly with a cloth that is then sorted out or used only for rough work.
How long do microfibre cloths last?
The service life depends more on care than on use. A cloth that is regularly washed without fabric softener, at moderate temperature and without direct heat remains absorbent much longer than a cloth from a hot wash with care additive.
A cloth should be sorted out when it has become hard, frayed, has holes or remains permanently stained. Such cloths are still usable for wheels, wheel arches, door shuts or work on the ground – they no longer have any place on paint.
Typical mistakes
- Using fabric softener: the most common mistake. The fibres lose their absorbency.
- Washing all cloths together: wheel dirt and polish residues spread onto paint-related cloths.
- Dosing too much: detergent residues remain in the fibre and later smear on glass and paint.
- Washing and drying too hot: the fibre hardens, the cloth becomes stiff.
- Leaving damp: odours set in and remain even after the next wash.
- Not checking: a frayed cloth continues to be used on paint although the edge scratches.
Storage and labelling
Dry cloths belong in a clean, closed container or a drawer, separated by area of use. Open shelves in the garage collect dust that reaches the surface on the next use. Never fold and store damp cloths – they must dry completely.
Simple labelling saves time: coloured edge, labelled laundry bag or a fixed order in the stack. A small supply sufficient for one wash plus a few spare cloths for the next load is practical.
Frequently asked questions
How often should I wash microfibre cloths?
After every use. Cloths that have come into contact with polish, wax or wheel dirt belong in the wash immediately; paint-related cloths from a clean wash can be collected until the next load but should not remain damp.
Can I wash microfibre cloths together with normal laundry?
Better not. Cotton fibres and lint lodge in the fine microfibres and reduce the effect. Wash cleaning cloths in their own load.
Why do my cloths no longer absorb water?
Most often fabric softener or a caring detergent additive is behind it, sometimes also too high temperatures during washing or drying. Wash the cloths several times without additives; absorbency often improves again.
Can I boil microfibre cloths?
No. High temperatures attack the fine fibres and make the cloth stiff. Work with a moderate temperature range and an extra rinse instead of high heat.
What do I do with worn-out cloths?
Continue using cloths with hard edges or holes for rough work, such as on wheels, wheel arches or door shuts. Afterwards they can be disposed of via residual waste; local disposal rules apply.